Using AI well How-tos Low effort10 min
Write lesson planning prompts that get a usable first draft
A seven-part prompt formula for AI lesson planning, with a before and after example and a 10-minute routine you can reuse every week.
What goes into a good lesson planning prompt?
A good prompt has seven parts: curriculum, year group, prior knowledge, objective, misconceptions, lesson length and output format. Leave one out and the AI fills the gap with a guess. The guess is usually generic.
- Curriculum: the subject and strand, such as KS2 maths fractions.
- Year group: Year 4, not ‘primary’.
- Prior knowledge: what pupils can already do, in one or two sentences.
- Objective: one thing pupils will be able to do by the end.
- Misconceptions: the one or two errors you expect to see.
- Lesson length: in minutes, such as 50.
- Output format: a table, a list or slide titles, plus extras such as four quiz questions.
Seven parts sounds long. Written as short lines, it takes about ten minutes.
What do you need before you start?
You need your scheme of work, one clear objective and ten minutes. Have these to hand before you open the AI tool:
- The unit, and where this lesson sits in it.
- A note on what the class did last lesson and what they found hard.
- Any fixed limits, such as no laptops or 15 mini whiteboards between 30 pupils.
- A blank document to build the prompt in, so you can reuse it.
Keep pupils’ names and personal data out of the prompt unless your school has approved the tool. Follow your school’s AI and data policy. This is not legal advice. Describe the class in general terms instead, such as ‘a mixed-attainment class of 28’.
What does a before and after prompt look like?
The before prompt is one line. The after prompt names all seven parts and is still only about 90 words.
Before:
Make me a lesson on fractions.
After:
I teach Year 4 in England. Maths, adding and subtracting fractions with the same denominator. Pupils can name the numerator and denominator and shade fractions of shapes, but have not added fractions yet. Objective: add two fractions with the same denominator, with answers up to one whole. Likely misconception: adding the denominators as well, so 1/5 + 2/5 becomes 3/10. The lesson is 50 minutes. Give me a table with timings, teacher talk, pupil task and a question to check understanding at each stage. End with four quiz questions and an answer key.
The first prompt leaves the AI to guess year group, length and format. The second removes each guess.
What are the steps, in order?
Write the parts in the same order every time, in about ten minutes in total.
- Write the curriculum and year group in one line (1 minute).
- Add prior knowledge in two sentences (2 minutes).
- State one objective, starting with a verb such as ‘add’ or ‘explain’ (1 minute).
- Name one or two misconceptions you expect (2 minutes).
- Give the lesson length in minutes (1 minute).
- Say exactly what output you want, such as a timed table and four quiz questions (2 minutes).
- Send it, then read the draft against your objective (1 minute for a first skim).
A fixed order means you never forget a part. It also makes it easy to spot which line to change when the draft is off.
What if the draft is wrong or you are out of energy?
Change one thing and ask again. Do not rewrite the whole prompt. Short follow-ups work well:
- Too generic: add one detail from your class, such as what they found hard last lesson.
- Too long: ask for the same plan cut to 40 minutes.
- Wrong level: restate the year group and prior knowledge.
- Wrong format: paste the format you want and ask for a redo.
If you have no energy left, send only three lines: year group, objective and lesson length. Fix the draft by hand.
The teacher always checks the output before it reaches pupils. Work through every maths answer and every fact yourself, and check that the timings add up to the lesson length.
What mistakes should you avoid?
The most common mistake is a vague objective such as ‘understand fractions’. The AI cannot plan towards something you cannot observe. Write what pupils will do instead.
- Asking for the lesson, slides, worksheet and homework in one prompt. Get the plan right first, then ask for resources.
- Leaving out lesson length, which gives you a plan for the wrong amount of time.
- Skipping misconceptions, so the plan never addresses the errors you will meet.
- Pasting in pupil names or personal data.
- Trusting the answer key without working the questions yourself.
- Starting a fresh chat for every tweak, which loses your context.
How can you make it easier next time?
Save your seven parts as a template with blank fields, and fill in only the three that change each lesson: objective, prior knowledge and misconceptions. That brings a repeat prompt down to about five minutes.
Some tools build these fields in. Planit Teachers lets you pick from 47 curriculum frameworks grouped by country. It is not the only option. Aila is free for teachers and uses Oak’s curriculum content.
To compare more options, see 4 AI tools for UK teachers that know the curriculum. Whichever you use, the same seven parts apply.
Frequently asked questions
How long should a lesson planning prompt be?
Long enough to cover the seven parts, which is usually a short paragraph. The example in this guide is about 90 words. Add more only where the AI keeps getting something wrong.
Do I need to name the curriculum in my prompt?
Yes. Without it the AI guesses which country and key stage you mean. Name the subject, the strand and the year group, such as Year 4 maths, fractions.
Can I put my class list into an AI tool?
No, not unless your school has approved the tool and its data policy allows it. Describe the class in general terms instead, such as a mixed-attainment class of 28. This is not legal advice, so follow your school's AI and data policy.
Should I write one big prompt or several small ones?
Start with one prompt for the lesson plan. Once the plan is right, ask for the worksheet, quiz or slides in follow-ups. This keeps each draft easier to check.
Does the same prompt work in any AI tool?
The seven parts work in any tool where you type instructions. Some tools use forms instead of a blank box, so you fill the same details into fields. Check the output yourself either way.